Sunday, January 30, 2011
IF HP C7280 Ink System Failure By freereset
Here are the details. Got the Ink System Failure message. The error code shows was '0xc18a0005'. The tech had me press and hold the '*' key on the key pad, then press the '#' key and release them both. Then he had me enter '123' to enter maintenance mode. He then had me press the right arrow (beside the OK button) until System Config. menu appeared on panel. Then pressed OK two times to clear the error condition, then cancel two or three times to return to the top menu. Then powered off and back on, printed a test page just fine, copied a document fine.
source:http://freereset.blogspot.com/2012/05/hp-c7280-ink-system-failure.html
Continue Reading..
source:http://freereset.blogspot.com/2012/05/hp-c7280-ink-system-failure.html
Saturday, January 29, 2011
Why use the Epson Resetter
Epson inkjet cartridges with "smart chips" send a signal to the printer when empty, and the printer won't recognize the refilled cartridge as it "remembers" it as empty. The resetter will "reset" the Epson chips to "full" specs.
Which Epson Resetter?
* Epson Resetter V1.0: For Epson inkjet cartridges with 7-pin chips
* Epson Resetter V2.0: For Epson plotter (wide format) cartridges with 7-pin chips
* Epson Resetter V3.0: For Epson inkjet cartridges with 9-pin chips (also backwards compatible with V1.0)
Continue Reading..
Which Epson Resetter?
* Epson Resetter V1.0: For Epson inkjet cartridges with 7-pin chips
* Epson Resetter V2.0: For Epson plotter (wide format) cartridges with 7-pin chips
* Epson Resetter V3.0: For Epson inkjet cartridges with 9-pin chips (also backwards compatible with V1.0)
Friday, January 28, 2011
Alternatives to the Canon Resetter
- Compatible Chips: Another method to overcome the "out of ink" signal that is sent
to the printer due to a spent inkjet cartridge is to replace the chip. Compatible chips are available on request.
Note: Images and instructions are property of Uni-Kit, an Easy Group brand and are protected by copyright laws
- Compatible Cartridges (with chips): Uni-Kit offers compatible or remanufactured Canon CLI-8 and PGI-5 cartridges with new, compatible chips.
- Manual overide procedure: Although this procedure may not work for all Canon printers, it is an option for customers to consider:
- Place the refilled cartridge (with the original "empty" chip) in the printer
- Press and hold the Reset/OK Button for 5 seconds to reset the chips.
- The "Ink Low" dialog box will pop up (similar to photo 1 below)
- Continue to print until the "ink has run out" dialog box pops up (similar to photo 2 Below) Click "OK" to continue to print.
- The "Ink Low" dialog box may reappear, if so repeat the first 2 steps
- Then the "once empty" dialog box will pop up (similar to photo 3 Below) Click "Yes" to continue to print
- The "Not Liable" dialog box will pop up (similar to photo 4 below). Click "Yes" to continue to print
- Continue to print until the "remaining level of ink" dialog box pops up (similar to photo 5 Below) Click "OK" to continue to print
- Another dialog box will pop up with the "press and hold the Resume" or "press and hold the Paper Feed" button (similar to photo 6). Press and hold the "STOP/RESET" button (for Canon MP Series) or "PAPER FEED" button (for Canon IP Series) for 5 seconds. DO NOT Click "Back" or "Cancel Printing"
- The "Ink Monitor" dialog box will appear and the printer will continue to print. (similar to photo 7) In the event that that the "press and hold the Resume " dialog box pops up again, Press and hold the Paper Feed Button or Stop/Reset Button for 5 seconds
Thursday, January 27, 2011
Why use the Canon Resetter
Canon CLI8 and PGI5 inkjet cartridges with "smart chips" send a signal to the printer when empty, and the printer won't recognize the refilled cartridge as it "remembers" it as empty. The resetter will "reset" the Canon chips to "full" specs.
Tuesday, January 25, 2011
Canon MPC190 Reset Waste Ink
Canon MPC190 ResetWaste Ink 1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan,Copy,Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returningto the state of 3)), and then press the [ON/OFF]key.
Continue Reading..
By pressing Menu, Copy, Scan,Copy,Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returningto the state of 3)), and then press the [ON/OFF]key.
CanonBJ F900, F890, F700, F500, S900, S820, S750 and S520
CanonBJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME buttontwo more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test print out, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change,and return to the top of the function selection menu. Pressing thePOWER button again turns off the printer for a rest
Continue Reading..
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME buttontwo more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test print out, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change,and return to the top of the function selection menu. Pressing thePOWER button again turns off the printer for a rest
Canon S9000 reset
CanonS9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMAiP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
Continue Reading..
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
Monday, January 24, 2011
CanonBJ-30 BJC-35v BJC-70 F14 Error Reset
CanonBJ-30 BJC-35v BJC-70 F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shut off printer
10: Unplug printer then re-plug printer
Continue Reading..
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shut off printer
10: Unplug printer then re-plug printer
Sunday, January 23, 2011
CanonBJC-50 BJC-55 BJC-80 BJC-85 M40 M70
CanonBJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
Continue Reading..
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
Saturday, January 22, 2011
CanonBJC-600 BJC-600e BJC-610 BJC-620
CanonBJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Continue Reading..
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Friday, January 21, 2011
Epson Stylus 660 user Manual
Your EPSON Stylus ® COLOR 660 printer is the ideal output device for small office or home printing. You can print anything from reports and resumes to photos and greeting cards with great results. The printer comes with these features: s Resolutions up to 1440 by 720 dpi (dots per inch), even on plain paper s EPSON’s exclusive Micro Piezo ™ ink jet technology for smaller, cleaner dots Four-color printing for photo-quality color and sharp black text on plain paper or a variety of special media s Great results on any paper size, including letter, legal, envelope, card, and panoramic paper s Creative software for implementing all your ideas for business or home. About Your Software The printer software CD-ROM includes all the software you need for printing: s Your printer driver runs your printer and lets you control how your documents look. get
Canon BJC-3000
Canon BJC-3000 BJC-6000BJC-6100 BJC-6200 S400 S450 F300 F600 F620CanonBJC-7000 BJC-7100BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three (3) times.The indicator should be orange.
6: Press Power to set data
Continue Reading..
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three (3) times.The indicator should be orange.
6: Press Power to set data
Thursday, January 20, 2011
CanonBJC-5100Self Test
CanonBJC-5100Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set dataService Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Continue Reading..
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set dataService Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Wednesday, January 19, 2011
CanonBJC-5000 reset
CanonBJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set data Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Continue Reading..
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set data Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Tuesday, January 18, 2011
CanonBJC-210 BJC-240BJC-250 BJC-255 BJC-265CanonBJC-4100 BJC-4200BJC-4300 BJC-4400 BJC-4550 BJC-4650
CanonBJC-210 BJC-240BJC-250 BJC-255 BJC-265CanonBJC-4100 BJC-4200BJC-4300 BJC-4400 BJC-4550 BJC-4650
1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME
Continue Reading..
1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME
Monday, January 17, 2011
Reset CanonBJC-2000 BJC-2100 Series
CanonBJC-2000 BJC-2100 Series
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET.
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Continue Reading..
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET.
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Sunday, January 16, 2011
SGH-E740 Manual Guide
The Samsung SGH-E740 is a mobile measuring 46 x 97 x 15.9 mm and weighs 92 grammes.Il embeds a digital camera of 2 megapixels, and an MP3 music player. Memory is expandable via microSD (Transflash) (up to 1 GB). These major points are multimedia player, expandable memory, stereo Bluetooth.download manual here
CanonBJC 1000 Series reset
CanonBJC 1000 Series
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Continue Reading..
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Saturday, January 15, 2011
CanonS450 Printer
CanonS450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times.The indicator should be orange.
7: Press Power to set data
Continue Reading..
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times.The indicator should be orange.
7: Press Power to set data
Opticom manual 3m
Here's a 3 M opticom can download user manuals, owner the instruction guide, repair, support, and 3m opticom share manual issues.
downloads3m opticom user's Guide3 M mpro120 Pocket projector manual
Here are 3 M mpro120 can download user manuals, owner the instruction guide, repair, support, and 3m mpro120 Pocket projector manual problem sharing.
3 M c1060 manual
Here are 3 M, you can download the c1060 user manuals, owner the instruction guide, repair, support, and 3m c1060 manual problem sharing.
downloads 3 M c1060 user's Guide3M dynatel 2273 manual
Here are 3 M dynatel 2273 you can download user manuals, owner the instruction guide, repair, support, and 3m dynatel 2273 manual problem sharing.
downloads3m dynatel 2273 user's Guide3 M-static sensor passive
Here are 3 M-you can download user manuals, owner the instruction guide, repair, support, and 3m 718 static sensor manual-sharing problems.
downloads3 M 718 for user's GuideFriday, January 14, 2011
Canon PIXMA iP1500 Waste Ink Counter Reset.
Step1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Canoni850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function 0 presses - green- Test print (or exit service mode on i960)1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960) 2 presses - green - EEPROM initialize 3 presses - orange- Reset waste ink counter
Continue Reading..
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Canoni850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function 0 presses - green- Test print (or exit service mode on i960)1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960) 2 presses - green - EEPROM initialize 3 presses - orange- Reset waste ink counter
Thursday, January 13, 2011
Canon i320, i255 Waste Ink Counter Reset.
Canon i320, i255 Waste Ink Counter Reset.
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.or
Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Continue Reading..
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.or
Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Canon Printer Waste Tank Reset
CanonGENERIC "S"SERIES RESET CODE
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Continue Reading..
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Wednesday, January 12, 2011
Reset Waste Ink Canon IP1500
Step 1 Manual for Service mode to reset waste ink or blinking canon ip1500
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 Use software for Permanent to reset waste ink
download tool to reset permanent waste ink.
this resetter printer Canon IP 1500. This tool can reset waste ink for canon ip1500 permanent
User guide:
1.
Unzip downloaded file.
2.
Run GeneralTool.exe
3.
Select the connected USB port number from USB port
4.
Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
5.
In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.
If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.
http://www.savefile.com/files/1039880
Continue Reading..
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 Use software for Permanent to reset waste ink
download tool to reset permanent waste ink.
this resetter printer Canon IP 1500. This tool can reset waste ink for canon ip1500 permanent
User guide:
1.
Unzip downloaded file.
2.
Run GeneralTool.exe
3.
Select the connected USB port number from USB port
4.
Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
5.
In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.
If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.
http://www.savefile.com/files/1039880
Tuesday, January 11, 2011
Canon Printer Waste Tank Reset
CanonGENERIC "S"SERIES RESET CODE
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Continue Reading..
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Service Manual 700/750C/750C PLUS/755CM Hp Designjet Plotters
This service manual contains information necessary to test, calibrate and service:
1. HP Designjet 700 plotters (models C4705A and C4706A)
2. HP Designjet 750C plotters (models C3195A and C3196A)
3. HP Designjet 750C Plus plotters (models C4708A and C4709A)
4. HP Designjet 755CM printers (models C3198A and C3198B)
For information about these plotters/printers, refer to the corresponding user and quick-reference guide
Table of contents HP Designjet 700/750C/750C PLUS/755CM Printer Service And Repair Manual
* Product Information
* Site Planning and Requirements
* Installation and Configuration
* Preventive Maintenance
* Functional Overview
* Removal and Replacement
* Calibrations and Adjustments
* Troubleshooting
* Print Quality
* Product History and Service Notes
* Parts and Diagrams
* Support Services
http://rapidshare.com/files/108116030/HP_DESIGNJET_700__750C__750CT__755CM_Service_Manual.rar
Continue Reading..
1. HP Designjet 700 plotters (models C4705A and C4706A)
2. HP Designjet 750C plotters (models C3195A and C3196A)
3. HP Designjet 750C Plus plotters (models C4708A and C4709A)
4. HP Designjet 755CM printers (models C3198A and C3198B)
For information about these plotters/printers, refer to the corresponding user and quick-reference guide
Table of contents HP Designjet 700/750C/750C PLUS/755CM Printer Service And Repair Manual
* Product Information
* Site Planning and Requirements
* Installation and Configuration
* Preventive Maintenance
* Functional Overview
* Removal and Replacement
* Calibrations and Adjustments
* Troubleshooting
* Print Quality
* Product History and Service Notes
* Parts and Diagrams
* Support Services
http://rapidshare.com/files/108116030/HP_DESIGNJET_700__750C__750CT__755CM_Service_Manual.rar
Oki c5300n drum resetting
Turn off the printer
Turn the printer on whilst holding down Menu button. (Display says user maintenance.)
Press the menu button three times. (The display will say drum counter reset.)
Press enter key. The system should go back on line, if not press on-line key.
Continue Reading..
Turn the printer on whilst holding down Menu button. (Display says user maintenance.)
Press the menu button three times. (The display will say drum counter reset.)
Press enter key. The system should go back on line, if not press on-line key.
Monday, January 10, 2011
Nokia 6125 service manual
Nokia 6125 is a smart phone manufactured and assembled by the Swedish company Nokia. In the following service manual, the step by step instruction, description, illustration and explanation is given. This service guide can be used as a reference to technician or anyone who has the intention to repair and troubleshoot their Nokia mobile phones properly. download it here
Error 6A00 on Canon PIXMA MP800
The 6A00 is a Canon generic code for paper path jam. Some where in the paper path a sensor is activated indicating paper jam so the printer will give off a 6A00 code. As a Canon tech, I usually find the code, almost 90% of the time, is related to the purge unit being jammed with something and not being able to move. Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like. And yes I have found all those things in a purge unit. The offending item needs to be removed or the purge unit needs replacement. A Pixma MP830 would still be under Canon warranty, get it into a shop and save yourself the hassel.
Incidently, the 6A00 error pertains to all Canon printers made in the last several years, its not just used in one model. And its always a paper path error or purge unit.
I forget myself so here goes, the purge unit, called a spittoon assembly in an HP, lexmark, and other inkjet printers, is where the print head assembly parks when not in use, also its other job is to clean and make sure the print head is clean and open for printing. That is why you'll find the print head assembly parked on top of it. It also has a an electrical pump to milk the print heads and test for ink flow.
Continue Reading..
Incidently, the 6A00 error pertains to all Canon printers made in the last several years, its not just used in one model. And its always a paper path error or purge unit.
I forget myself so here goes, the purge unit, called a spittoon assembly in an HP, lexmark, and other inkjet printers, is where the print head assembly parks when not in use, also its other job is to clean and make sure the print head is clean and open for printing. That is why you'll find the print head assembly parked on top of it. It also has a an electrical pump to milk the print heads and test for ink flow.
Saturday, January 1, 2011
Privacy policy
If you require any more information or have any questions about our privacy policy, please feel free to contact us by email at alfree.b@hotmail.com.
At www.usermanualfree.blogspot.com, the privacy of our visitors is of extreme importance to us. This privacy policy document outlines the types of personal information is received and collected by www.usermanualfree.blogspot.com and how it is used.
Log Files
Like many other Web sites, www.usermanualfree.blogspot.com makes use of log files. The information inside the log files includes internet protocol ( IP ) addresses, type of browser, Internet Service Provider ( ISP ), date/time stamp, referring/exit pages, and number of clicks to analyze trends, administer the site, track user’s movement around the site, and gather demographic information. IP addresses, and other such information are not linked to any information that is personally identifiable.
Cookies and Web Beacons
www.usermanualfree.blogspot.com does use cookies to store information about visitors preferences, record user-specific information on which pages the user access or visit, customize Web page content based on visitors browser type or other information that the visitor sends via their browser.
DoubleClick DART Cookie
.:: Google, as a third party vendor, uses cookies to serve ads on www.usermanualfree.blogspot.com.
.:: Google's use of the DART cookie enables it to serve ads to users based on their visit to www.usermanualfree.blogspot.com and other sites on the Internet.
.:: Users may opt out of the use of the DART cookie by visiting the Google ad and content network privacy policy at the following URL - http://www.google.com/privacy_ads.html
Some of our advertising partners may use cookies and web beacons on our site. Our advertising partners include ....
Google Adsense
These third-party ad servers or ad networks use technology to the advertisements and links that appear on www.usermanualfree.blogspot.com send directly to your browsers. They automatically receive your IP address when this occurs. Other technologies ( such as cookies, JavaScript, or Web Beacons ) may also be used by the third-party ad networks to measure the effectiveness of their advertisements and / or to personalize the advertising content that you see.
www.usermanualfree.blogspot.com has no access to or control over these cookies that are used by third-party advertisers.
You should consult the respective privacy policies of these third-party ad servers for more detailed information on their practices as well as for instructions about how to opt-out of certain practices. our privacy policy does not apply to, and we cannot control the activities of, such other advertisers or web sites.
If you wish to disable cookies, you may do so through your individual browser options. More detailed information about cookie management with specific web browsers can be found at the browsers' respective websites.
Continue Reading..
At www.usermanualfree.blogspot.com, the privacy of our visitors is of extreme importance to us. This privacy policy document outlines the types of personal information is received and collected by www.usermanualfree.blogspot.com and how it is used.
Log Files
Like many other Web sites, www.usermanualfree.blogspot.com makes use of log files. The information inside the log files includes internet protocol ( IP ) addresses, type of browser, Internet Service Provider ( ISP ), date/time stamp, referring/exit pages, and number of clicks to analyze trends, administer the site, track user’s movement around the site, and gather demographic information. IP addresses, and other such information are not linked to any information that is personally identifiable.
Cookies and Web Beacons
www.usermanualfree.blogspot.com does use cookies to store information about visitors preferences, record user-specific information on which pages the user access or visit, customize Web page content based on visitors browser type or other information that the visitor sends via their browser.
DoubleClick DART Cookie
.:: Google, as a third party vendor, uses cookies to serve ads on www.usermanualfree.blogspot.com.
.:: Google's use of the DART cookie enables it to serve ads to users based on their visit to www.usermanualfree.blogspot.com and other sites on the Internet.
.:: Users may opt out of the use of the DART cookie by visiting the Google ad and content network privacy policy at the following URL - http://www.google.com/privacy_ads.html
Some of our advertising partners may use cookies and web beacons on our site. Our advertising partners include ....
Google Adsense
These third-party ad servers or ad networks use technology to the advertisements and links that appear on www.usermanualfree.blogspot.com send directly to your browsers. They automatically receive your IP address when this occurs. Other technologies ( such as cookies, JavaScript, or Web Beacons ) may also be used by the third-party ad networks to measure the effectiveness of their advertisements and / or to personalize the advertising content that you see.
www.usermanualfree.blogspot.com has no access to or control over these cookies that are used by third-party advertisers.
You should consult the respective privacy policies of these third-party ad servers for more detailed information on their practices as well as for instructions about how to opt-out of certain practices. our privacy policy does not apply to, and we cannot control the activities of, such other advertisers or web sites.
If you wish to disable cookies, you may do so through your individual browser options. More detailed information about cookie management with specific web browsers can be found at the browsers' respective websites.